Hammer mill is a common equipment in wood processing factory and wood pellet plant. It serves to crush wood materials into powders so that they can be used to make wood pellet fuel and other wood products. It can process pines, poplar, cedar, bamboo, weed tree, and various fiber materials like rice straw, cotton stalk, twitch grass, etc. Hammer mill applies to materials whose diameter is 10-30mm, and reduce their size to 3-5mm.
Note: If you are interested in our products, please submit your requirements and contact information, and then we will contact you within 24 hours, welcome your message.
Hammer mill is the most widely used wood crusher. It use high-speed rotating hammers to crush the wood materials. Hammer mill features simple structure, wide applicability, high product efficiency, and easy operation.
A hammer mill is mainly composed of 3 parts, the feed hopper, the pulverizing room includes rotator, hammers, screener, toothed plates, and the discharge part includes wind blower, aggregate cylinder, dust bag.
First, you feed the wood materials into the feed hopper and they will fall into the pulverizing room. In the pulverizing room, the wood materials are beaten by the high-speed rotating hammer and bounce to the toothed plates, then they bounce back and repeat this process. Meanwhile, the materials are grinded between the hammers and screener. Under the beating, collision and friction of the hammers, toothed plates and screener, the wood materials are crushed into small particles until they are small enough to get through the screener.
Then, the crushed wood materials are pumped out through the screener by the blower. There is a wood powder collector a aggregate cylinder or a dust bagthat separate the air from the final products. If the hammer mill isnrsquot equipped with a wind blower, the crushed materials will be expelled out by the airflow in the pulverizing room.
According to the shape of screener, hammer mill can be classified into half-screen hammer mill, full-screen hammer mill, and screenless hammer mill. According to the size and production capacity, it can be classified into small hammer mill and large hammer mill.
Small hammer mill is also called half-screen hammer mill, because the screen cloth is a semicircle covering the lower part of the rotor. The toothed plate is installed in the upper body. Raw materials are fed along the tangent line of the crushing chamber.
A hammer mill is composed of a feed hopper, discharge hopper, engine body, air blower, rotator fixed with hammers, screen cloth, cyclone, etc.
Small hammer mill is a general type. It adapt to different working conditions. It features small size, low cost and easy operation. Small hammer mills are usually applied in farm, small feed mill, small pellet production line, and wood processing plant.
DescriptionHammers Several Varieties Sizes Spacers Pins Spare Screen Cradle Locking Collars Legacy Mill Parts We can restore your old Prater DF Mill to like-new condition Praters Customer Service and Support Team stands Industry Application Crushers Grinding Mills.
DescriptionScreen Dividers Top and Bottom Screens Hammer Pins Support Pins Spacers Washers Hammers Several Varieties Sizes Praters Customer Service and Support Team stands ready to support you. Simply contact us by Industry Application Crushers Grinding Mills.
DescriptionOur H79 alloy steel hammers provide reliable, consistent service for secondary and primary crushers. H79 is a high strength alloy steel with a hardness of 477-512 HB. The hardness provides very good resistance to abrasive wear. H79 is also very tough and has Charpy V-notch impact test results Industry Application Crushers Grinding Mills.
Descriptionfacets of the manufacturing process, we provide our customers with the highest quality parts with our professional service. Another strong advantage is our MILL SHIPMENT division, Interfast Group is knowledgeable and experienced in the manufacturing and distribution of all types of Type Other.
DescriptionThe RH disintegrator machine circulates and disperses mixtures, eliminates lumps and creates a suspension or emulsion simultaneously. Designed for high-intensity mixing and grinding in homogenization applications All stainless steel product-contact parts for sanitary Equipment Types Hammer Cage MillFeed Batch, ContinuousIndustry or Material Processed Food Processing Grain, SanitaryProcess Type Dry, Wet.
Descriptionfor cleaning and internal part replacement Hammers are mounted directly onto the motor shaft to minimize maintenance and reduce product contamination Available in sanitary construction for use in FDAUSDA inspected plants RA and RP Series Disintegrators are widely.
Descriptionrebuilding worn parts to near final dimensions before applying final hardfacing layers which are more wear resistant Unlimited layers Typical Applications Tractor rolls and idlers Shovel parts Mill and crusher hammers Mine car wheels Dredge pumps Welding Positions Flat Alloy Type Hardfacing Repair AlloyDiameter Thickness 0.0450 to 0.1094 inchWelding Process Form Flux CorednbspWire, Other.
Descriptioncheck and are usually best limited to two layers Typical Applications Boom heels Conveyor screws Dipper lips Tractor grousers Ditcher teeth Lumber equipment Hammer mills Welding PositionsAll, except vertical down Alloy Type Hardfacing Repair AlloyDiameter Thickness 0.1250 to 0.1875 inchWelding Process Form Other.
Description, interpass temperatures and procedures Use on mild and low alloy steels Typical Applications Build-Up shovel and bucket lips, pump impellers and housings, pulverizer plows, and mill hammers Hardfacing trunions, tractor rolls, cranes and gears Welding Positions Flat and horizontal Alloy Type Hardfacing Repair AlloyDiameter Thickness 0.1562 to 0.1875 inchWelding Process Form Other.
A wide variety of hammer mill parts options are available to you, There are 2,147 suppliers who sells hammer mill parts on Alibaba.com, mainly located in Asia. The top countries of supplier is China, from which the percentage of hammer mill parts supply is 100 respectively.
A hammer is a handheld tool used to strike another object. It consists of a handle to which is attached a heavy head, usually made of metal, with one or more striking surfaces. There are dozens of different types of hammers. The most common is a claw hammer, which is used to drive and pull nails. Other common types include the ball-peen hammer and the sledge hammer.
The concept of using a heavy object to strike another object predates written history. The use of simple tools by our human ancestors dates to about 2,400,000 B.C. when various shaped stones were used to strike wood, bone, or other stones to break them apart and shape them. Stones attached to sticks with strips of leather or animal sinew were being used as axes or hammers by about 30,000 B.C. during the middle of the Old Stone Age.
Modern hammers come in a variety of shapes, materials, and weights. Although some specialty hammers are no longer used, there is still a wide array of hammer configurations as new designs are developed for new applications.
A related class of hammer-like tools are called mallets. They have large heads made of rubber, plastic, wood, or leather. Mallets are used to strike objects that would be damaged by a blow from a metal hammer. Rubber mallets are used to assemble furniture or to beat dents out of metal. Wood and leather mallets are used to strike wood handled chisels. Plastic mallets have smaller heads and are used to drive small pins into machinery. A very large wooden mallet is sometimes called a maul.
The two major components of a hammer are the head and the handle. The design of these two components depends on the specific application, but all hammers have many common features.
The striking surface of the head is called the face. It may be flat, called plain faced, or slightly convex, called bell faced. A bell-faced hammer is less likely to bend a nail if the nail is struck at an angle. Another face design is called a checkered face. It has crosshatched grooves cut into the surface to prevent the hammer from glancing off the nail head. Because it leaves a checkered impression on the wood, it is usually only found on framing hammers used for rough construction.
If you are interested in our products, or have any questions for us, you can click the button below